#
# TANIKAWA Tatsuya
#
# for SS-R575
#

machine		"i386"
#cpu		"I386_CPU"
cpu		"I486_CPU"
cpu		"I586_CPU"		# aka Pentium(tm)
#cpu		"I686_CPU"		# aka Pentium Pro(tm)

ident		TANIKAWA
maxusers	10

#options		MATH_EMULATE		#Support for x87 emulation

# When this is set, be extra conservative in various parts of the kernel
# and choose functionality over speed (on the widest variety of systems).
options		FAILSAFE

#
# This directive defines a number of things:
#  - The compiled kernel is to be called `kernel'
#  - The root filesystem might be on partition wd0a
#  - Crash dumps will be written to wd0b, if possible.  Specifying the
#    dump device here is not recommended.  Use dumpon(8).
#
config		kernel	root on wd0 dumps on wd0

#####################################################################
# COMPATIBILITY OPTIONS                                             

#
# Implement system calls compatible with 4.3BSD and older versions of
# FreeBSD.  You probably do NOT want to remove this as much current code
# still relies on the 4.3 emulation.
#
options		"COMPAT_43"
#
# Allow user-mode programs to manipulate their local descriptor tables.
# This option is required for the WINE Windows(tm) emulator, and is
# not used by anything else (that we know of).
#
options		USER_LDT		#allow user-level control of i386 ldt
#
# These three options provide support for System V Interface
# Definition-style interprocess communication, in the form of shared
# memory, semaphores, and message queues, respectively.
#
options		SYSVSHM
options		SYSVSEM
options		SYSVMSG
#
# This option includes a MD5 routine in the kernel, this is used for
# various authentication and privacy uses.
#
options		"MD5"

#####################################################################
# DEBUGGING OPTIONS

#
# Enable the kernel debugger.
#
#options		DDB
#
# Don't drop into DDB for a panic. Intended for unattended operation
# where you may want to drop to DDB from the console, but still want
# the machine to recover from a panic
#
#options		DDB_UNATTENDED
# 
# KTRACE enables the system-call tracing facility ktrace(2).
#
#options		KTRACE			#kernel tracing
#
# The DIAGNOSTIC option is used in a number of source files to enable
# extra sanity checking of internal structures.  This support is not
# enabled by default because of the extra time it would take to check
# for these conditions, which can only occur as a result of
# programming errors.
#
#options		DIAGNOSTIC

#
# PERFMON causes the driver for Pentium/Pentium Pro performance counters
# to be compiled.  See perfmon(4) for more information.
#
options		PERFMON

# XXX - this doesn't belong here.
# Allow ordinary users to take the console - this is useful for X.
options		UCONSOLE

# XXX - this doesn't belong here either
options		USERCONFIG		#boot -c editor
#options		USERCONFIG_BOOT		#imply -c and parse info area
options		VISUAL_USERCONFIG	#visual boot -c editor

#####################################################################
# NETWORKING OPTIONS

#
# Protocol families:
#  Only the INET (Internet) family is officially supported in FreeBSD.
#  Source code for the NS (Xerox Network Service) is provided for amusement
#  value.
#
options		INET			#Internet communications protocols

#
# Network interfaces:
#
pseudo-device	ether			#Generic Ethernet
pseudo-device	loop			#Network loopback device
#pseudo-device	sl	1		#Serial Line IP
#pseudo-device	ppp	1		#Point-to-point protocol
pseudo-device	bpfilter	4	#Berkeley packet filter
pseudo-device	tun	1		#Tunnel driver(user process ppp)

#
# Internet family options:
#
options		MROUTING		# Multicast routing

#####################################################################
# FILESYSTEM OPTIONS

# One of these is mandatory:
options		FFS			#Fast filesystem
options		NFS			#Network File System

# The rest are optional:
# options	NFS_NOSERVER		#Disable the NFS-server code.
#options		"CD9660"		#ISO 9660 filesystem
#options		MFS			#Memory File System
options		MSDOSFS			#MS DOS File System
options		PROCFS			#Process filesystem

# Make space in the kernel for a MFS root filesystem.  Define to the number
# of kilobytes to reserve for the filesystem.
#options		MFS_ROOT=10
# Allow the MFS_ROOT code to load the MFS image from floppy if it is missing.
#options		MFS_AUTOLOAD

#####################################################################
# SCSI DEVICES

# SCSI DEVICE CONFIGURATION

controller	scbus0	#base SCSI code
device		ch0	#SCSI media changers
device		sd0	#SCSI disks
device		st0	#SCSI tapes
device		cd0	#SCSI CD-ROMs
device		od0	#SCSI optical disk

# SCSI OPTIONS:

# SCSIDEBUG: When defined enables debugging macros
# NO_SCSI_SENSE: When defined disables sense descriptions (about 4k)
# SCSI_REPORT_GEOMETRY: Always report disk geometry at boot up instead
#                       of only when booting verbosely.
#options		SCSIDEBUG
#options		NO_SCSI_SENSE
#options		SCSI_REPORT_GEOMETRY

# More undocumented options for linting.
options		SCSI_DELAY=5	# Be pessimistic about Joe SCSI device

#####################################################################
# MISCELLANEOUS DEVICES AND OPTIONS

pseudo-device	pty	32	#Pseudo ttys - can go as high as 256
pseudo-device	speaker		#Play IBM BASIC-style noises out your speaker
pseudo-device	log		#Kernel syslog interface (/dev/klog)
pseudo-device	gzip		#Exec gzipped a.out's
pseudo-device	vn		#Vnode driver (turns a file into a device)

#####################################################################
# HARDWARE DEVICE CONFIGURATION

#
# Mandatory ISA devices: isa, sc or vt, npx
#
controller	isa0

#
# Options for `isa':
#
#options		BOUNCE_BUFFERS

# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device		vt0	at isa? port "IO_KBD" tty irq 1 vector pcrint
#options		PCVT_FREEBSD=210	# pcvt running on FreeBSD >= 2.0.5
#options		XSERVER			# include code for XFree86
#options		FAT_CURSOR		# start with block cursor
# This PCVT option is for keyboards such as those used on IBM ThinkPad laptops
#options		PCVT_SCANSET=2 		# IBM keyboards are non-std

# The syscons console driver (sco color console compatible) - default.
device		sc0	at isa? port "IO_KBD" tty irq 1 vector scintr
options		MAXCONS=4		# number of virtual consoles
#options		SLOW_VGA		# do byte-wide i/o's to TS and GDC regs

#
# This device is mandatory.
#
# The Numeric Processing eXtension is used to either enable the
# coprocessor or enable math emulation.  If your machine doesn't contain
# a math co-processor, you must *also* add the option "MATH_EMULATE".
# THIS IS NOT AN OPTIONAL ENTRY, DO NOT REMOVE IT
device		npx0	at isa? port "IO_NPX" iosiz 0x0 flags 0x0 irq 13 vector npxintr

#
# Optional ISA and EISA devices:
#

#
# SCSI host adapters: `aha', `aic', `bt', `nca'
#
controller      aic0    at isa? port 0x340 bio irq 11 vector aicintr

#
# ST-506, ESDI, and IDE hard disks: `wdc' and `wd'
#
controller	wdc0	at isa? port "IO_WD1" bio irq 14 vector wdintr
disk		wd0	at wdc0 drive 0
#disk		wd1	at wdc0 drive 1
#controller	wdc1	at isa? port "IO_WD2" bio irq 15 vector wdintr
#disk		wd2	at wdc1 drive 0
#disk		wd3	at wdc1 drive 1

#
# ATAPI enables the support for ATAPI-compatible IDE devices
#
#options		ATAPI	#Enable ATAPI support for IDE bus
#options		ATAPI_STATIC	#Don't do it as an LKM
# IDE CD-ROM driver - requires wdc controller and ATAPI option
#device          wcd0

#
# Standard floppy disk controllers and floppy tapes: `fdc', `fd', and `ft'
#
controller	fdc0	at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr
disk		fd0	at fdc0 drive 0
disk		fd1	at fdc0 drive 1
tape		ft0	at fdc0 drive 2

#
# Other standard PC hardware: `lpt', `mse', `psm', `sio', etc.
#
device		lpt0	at isa? port? tty irq 7 vector lptintr
#device		lpt1	at isa? port "IO_LPT3" tty irq 5 vector lptintr
#device		mse0	at isa? port 0x23c tty irq 5 vector mseintr
device		psm0	at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr
# Options for psm:
#options		PSM_CHECKSYNC		#checks the header byte for sync.

device		sio0	at isa? port "IO_COM1" tty irq 4 vector siointr
device		sio1	at isa? port "IO_COM2" tty irq 3 vector siointr
device		sio2	at isa? port "IO_COM3" tty irq 9 vector siointr

#
# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
#
device ed0 at isa? port 0x280 net irq 5 iomem 0xd8000 vector edintr
device ep0 at isa? port 0x300 net irq 10 vector epintr
device fe0 at isa? port 0x300 net irq ? vector feintr

#
# Audio drivers: `snd', `sb', `pas', `gus', `pca'
#

# Controls all sound devices
controller	snd0
device sb0      at isa? port 0x220 irq 5 drq 1 vector sbintr
# For normal case use next line
device opl0     at isa? port 0x388

options SBC_IRQ=5		#PAS-16. Must match irq on sb0 line.

# Not controlled by `snd'
device pca0 at isa? port IO_TIMER1 tty

#
# Miscellaneous hardware:
#
device		apm0	at isa?
#options		APM_BROKEN_STATCLOCK

#####################################################################
# PAO CONFIGURATION

#
# PCCARD/PCMCIA
#
# crd: slot controller
# pcic: slots

# Dont remove these two lines!
controller	crd0
device		pcic0   at crd?
#device		pcic1   at crd?

# laptop-specific configuration
#options		LAPTOP

# If your laptop have not had Windoze95-Ready BIOS, please update it.
# Such old BIOS'es sometimes have critical bugs at 32-bit protected
# mode APM BIOS interface (which have not used by Windoze 3.1).

# PC-card suspend/resume support (experimental)
options		APM_PCCARD_RESUME
options		PCIC_RESUME_RESET

# Keep power for serial cards when the system suspends
# (If your machine hangs up when you try to suspend the system with
#  FAX/Modem PCMCIA card, uncomment this option).
#options	SIO_SUSP_KEEP_PWR

# Detach SCSI devices when the SCSI card is removed
options		SCSI_DETACH

# Some PCI Laptop machines probe PC-card controller twice (via ISA and
# PCI bus).  This option disables PC-card probe routine when the PC-card
# controller has already been probed via PCI bus.
#options	PCIC_PCI_ISA_CONFLICT

# Some PCI Laptop machine reports invalid slot number when the card is
# inserted or removed.  It is prevented by specifying the number of slot
# explicitly. Otherwise, this number is detected automatically.
#options	"PCIC_MAX_SLOTS=2"

# Japanese version of WaveLAN PCMCIA uses 2.4GHz band instead of 915MHz
# band that US version uses.  If you want to use Japanese version of
# WaveLAN, uncomment this line, or edit the corresponding config entry
# of /etc/pccard.conf.
#options	"WAVELAN_PCMCIA_24"

# Suspend the system when the battery status is "Low"
#options	"APM_BATT_LOW_SUSPEND"

# If you want to use NTP on laptop machines, uncomment the following 
# option.  Current APM implementation affects NTP client.
#options	"APM_NO_CLOCK_ADJUST"

# Don't suspend the system immediately before the system is resumed
# from suspended mode (Default 3 seconds)
#options		"APM_NOSUSPEND_IMMEDIATE=3"

# If your machine says that PC-cards are inserted and removed frequently
# even if you don't insert or remove the cards, please try to specify
# the IRQ of PCIC explicitly.
#options	"PCIC_IRQ=12"		# for machines with serial trackball
#options	"PCIC_IRQ=0"		# zero means no IRQ mode

# Some PCMCIA-PCI bridge has peculiar I/O address (default: 0x3e0).  
# If you want to specify I/O address explicitly, uncomment and edit the
# following line (for example, I/O address of PCMCIA bridge of SOTEC 
# Winbook Quattro/V is 0x3000).  To know this value, please read the
# manual of your laptop or device property of PCMCIA bridge from
# Windows95's device control panel.
#options	"PCIC_IO=0x3000"	# for Sotec Winbook Quattro/V